The Use of a Two Stage Dimensional Variation Analysis Model to Simulate the Action of a Hydraulic Tappet Adjustor in a Car Engine Valve Train System

L.C. Sleath^1, and P.G. Leaney¹

¹Department of Mechanical and Manufacturing Engineering, Loughborough University, Loughborough, UK

Cite this paper:
L.C. Sleath and P.G. Leaney. The Use of a Two Stage Dimensional Variation Analysis Model to Simulate the Action of a Hydraulic Tappet Adjustor in a Car Engine Valve Train System. American Journal of Vehicle Design. 2013; 1(2):36-43. doi: 10.12691/ajvd-1-2-4

Abstract

Dimensional variation analysis (DVA) models have been used in the manufacturing industry for over 20 years to predict how minor variations in the size, shape and location of the components parts is likely to propagate throughout and affect the overall dimensions, operation and performance of a complete mechanical system. This paper is one of in series of four papers that describe how different techniques can be utilised to aid the creation and application of DVA models. This paper explains the development and use of a two stage DVA model to simulate the action of a hydraulic tappet adjuster and dimensional interdependence that exists between the adjustment of a hydraulic tappet and the actuation (opening & closing) of the cylinder valve. The three other papers cover the use of kinematic constraint maps to prepare the structure of a DVA model; the use of virtual fixtures, jigs and gauges to achieve the necessary component location and the required variation measurements, and the use of 3D plots to display large numbers of DVA results as a single 3D shape. A hydraulic tappet adjustor performs two functions; it is part of the valve train system that actuates (opens & closes) the cylinder valve and it also self adjusts to take up any free play in the valve train system. These two functions, tappet adjustment and valve actuation, are separate operations that occur at different times during the valve train operating cycle and so need to be modelled as different configurations in a DVA model. In a conventional multiple configuration DVA model, each configuration has to be fully constrained and mathematically closed independently of any other model configuration. This requirement makes it difficult to include the interdependence between tappet adjustment and valve actuation. The two stage approach overcomes this limitation by allowing the output variation from the tappet setting configuration to be carried over into the valve actuation configuration and can thereby fully account for the interdependence between the two operations.

Keywords:
Dimensional variation analysis Engine valve train dimensional variation behaviour

This work is licensed under a Creative Commons Attribution 4.0 International License. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/

Figures

References:

[1]	Harper, A.P, Jaguar’s approach to dimensional control in product development, colloquium on dimensional variation (Digest No 1997/346) 1997.
[2]	Cleverly, D.J, Olifent, A.M.D, Rover’s approach to dimensional variation, colloquium on dimensional variation (Digest No 1997/346) 1997.
[3]	McFadden, C.D, Application of system design tools to integrate product development process, MSc thesis, University of South Carolina, 2005.
[4]	Zheng, L.Y, McMahon, C.A, Li1, L, Ding L, Jamshidi, J, Key characteristics management in product lifecycle management: a survey of methodologies and practices, Proc. IMechE Vol. 222 Part B: 2008.
[5]	Day, J, 787 Dimensional management, Boeing Corporation, 2005, available from http://www.lvmc.org.uk., accessed June 2013.
[6]	Astles, S, Dimension management, the reasons for change, AirbusUk, 2005, available from http://www.3dcs.com/downloads/airbus.pdf, accessed June 2013.
[7]	Robert, E.B, Best practice: F-22 variability reduction, Lockheed Martin, 2005, available from http://www.bmpcoe.org/bestpractices/internal/lmtas/lmtas_18.html, accessed June 2013.
[8]	Pritchett, J, losing the loop of the digital thread”, Lockheed Martin, 2005, available from http://web.mit.edu/lmp/Presentations/Pritchett-Lockheed.pdf, accessed June 2013.
[9]	Spicknall, M.H, Kumar, R, and Huang, T.D, Dimensional management in shipbuilding: a case study fromthe Northrup Grumman Ship Systems Lightweight Structures Project, J. Ship Prod., 2005, 21(4), 209-218.
[10]	Jeffreys, D, Leaney, P.G, Dimensional control as an integral part of next-generation aircraft development, Proc. Instn. Mech. Engrs, Part B: J. Engineering Manufacture, 2000, 214(B9), 831-835.
[11]	Craig, M, Variation by design, Mechanical Engineering, 110, pp52-54, November 1988.
[12]	Craig, M, Dimensional management versus tolerance assignment, Assembly Automation, Volume 16, Number 2, 1996, 12-16.
[13]	Craig, M, Dimensional management: a necessary process to meet corporate goals for global competition, colloquium on dimensional variation (Digest No 1997/346) 1997.
[14]	Ceglarek, D, Shi, J, Dimensional variation reduction for automotive body assembly, Mfg Rev., 1995, 8(2), 139-154.
[15]	Loose, J.P, Zhou, O, Zhou, S, Ceglarek, D, Integrating GD&T into dimensional variation models for multistage machining processes, International Journal of Production Research, Vol. 48, No. 11, 1 June 2010, 3129-3149.
[16]	Sleath, D.M, Leaney, P.G, Control of dimensional variation and integrated product development, colloquium on dimensional variation (Digest No 1997/346) 1997.
[17]	Booker, J.D, Swift, K.G, Brown, N.J, Designing for assembly quality: strategies, guidelines and techniques, Journal of Engineering Design, 16:3, 279-295.
[18]	Dresner, T, Barkan, P, A review and classification of variable valve timing mechanisms, Technical paper 890674, Society of Automotive Engineers congress and exposition, Detroit, MI, USA , 27 Feb-3 Mar 1989.
[19]	Li, L, Tao, J, Wang, Y, Su, Y, Xiao, M, Effects of intake valve closing timing on gasoline engine performance and emissions, SAE Technical Paper 2001-01-3564, 2001.
[20]	Siewert, R.M, How individual valve timing events affect exhaust emissions, SAE Technical Paper 710609, 1971.
[21]	Takemura, S, Aoyama, S, Sugiyama, T, Nohara, T, Moteki, K, Nakamura, M, Hara, S,A study of a continuous variable valve event and lift (VEL) system, SAE Technical Paper 2001-01-0243, 2001.
[22]	Wong, P.K, Tam, L. M, Li, K, Modelling and simulation of a dual mode electro hydraulic fully variable valve train for four stroke engines, International Journal of Automotive Technology: Vol 9, No5, pp 509-521, 2008.
[23]	Sleath, L.C, Leaney, P.G, The use of virtual fixtures, jigs and gauges in dimensional variation analysis models, Loughborough University, 2013.