Manifold Technology in the Offshore Industry

Karan Sotoodeh^1,

¹Valve Engineering, Baker Hughes, Oslo, Norway

Cite this paper:
Karan Sotoodeh. Manifold Technology in the Offshore Industry. American Journal of Marine Science. 2020; 8(1):14-19. doi: 10.12691/marine-8-1-3

Abstract

Manifolds are widely used in the oil and gas industry for the distribution of process fluids such as oil, gas, and water. Manifolds are designed to either merge multiple junctions into a single channel or divide one flow line to multiple outputs. The size of a manifold is selected by process engineers based on the flow rate passing through the manifold. Manifolds used in the offshore industry are made in 22Cr duplex instead of carbon steel to save thickness and weight. The manifolds described in this paper are either made of welding wrought tees or designed using a standard pipe as a header and welding olets to the pipe header. Mechanical joints (hubs and clamps) instead of standard ASME flanges are used for closing some of the manifold header ends as well as some of the branch connections to save weight and space. Traditionally, welding techniques and preparation of the welded ends has been done as per ASME B16.25, the common standard for butt welded connections in piping systems, including manifolds. However, narrow gap welding is an advanced welding end preparation in which the angle of the bevel end fitting is 7° to the vertical line. The advantages of narrow gap welding include using less weld electrodes, a faster welding process, and less heat input. This paper presents a method for calculating welding consumables volume and weight in one meter. The result shows that the amount of welding electrodes used for standard ASME welding is more than double the amount used for narrow gap welding.

Keywords:
manifold manufacturing process material selection welding oil and gas offshore

This work is licensed under a Creative Commons Attribution 4.0 International License. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/

References:

[1]	Honiron. (2018). Manifold application in the oil and gas industry. [Online]. Available from: https://www.honiron.com/manifold-applications-oil-gas-industry/.
[2]	Rigzone. (2018). How does gas injection work? [Online]. Available from: https://www.rigzone.com/training/insight.asp?insight_id=345.
[3]	American Society of Mechanical Engineering B16.5. (2012). Piping flanges and flanged fittings. New York, NY: ASME.
[4]	Sotoodeh, K. (2018). Analysis and improvement of material selection for process piping system in offshore industry. American Journal of Mechanical Engineering, Vol.6, No. 1, p. 17-26.
[5]	NORSOK L-001, (2017). Piping and valves. 4th revision, Oslo, Norway.
[6]	American Society of Mechanical Engineering B16.9. (2012). Factory made wrought buttwelding fittings. New York, NY: ASME.
[7]	American Society of Mechanical Engineers (ASME). (2004). Carbon, alloy and stainless steel pipes. ASME B36.10/19. New York, NY: ASME.
[8]	Manufacturers Standardization Society of the Valve and Fittings Industry, MSS SP 97. (2002). Integrally reinforced forged branch outlet fittings- socket welding, threaded and butt-welded ends. Vienna, VA: MSS.
[9]	Hardhatengineer. (2018). Pipe fitting manufacturing process [Online]. Available from: https://hardhatengineer.com/pipe-fittings/pipe-fittings-manufacturing-process/
[10]	American Society of Mechanical Engineers (ASME B31.3). (2012). Process piping. New York, NY: ASME.
[11]	American Society of Mechanical Engineers (ASME B16.5). (2017). Butt welding ends. New York, NY: ASME.
[12]	Cristini S. I., Sacchi, B., Guerrini, E., & Trasatti, S. (2010). Detection of Sigma phase in 22Cr duplex stainless steel by electrochemical methods. Russian Journal of Electrochemistry. Vol.46, No.10, pp.1168–1175.
[13]	The Welding Institute (2018). Calculating weld volume and weight. [Online]. Available from: https://www.twi-global.com/technical-knowledge/job-knowledge/calculating-weld-volume-and-weight-095/.