Numerical Simulation and Experiments of Barite Sag in Horizontal Annulus

Yahya Hashemian¹, Stefan Miska^1, , Mengjiao Yu¹, Evren Ozbayoglu¹ and Nicholas Takach¹

¹Petroleum Enginerring Department, University of Tulsa, Tulsa, USA

Cite this paper:
Yahya Hashemian, Stefan Miska, Mengjiao Yu, Evren Ozbayoglu and Nicholas Takach. Numerical Simulation and Experiments of Barite Sag in Horizontal Annulus. American Journal of Numerical Analysis. 2014; 2(1):14-19. doi: 10.12691/ajna-2-1-4

Abstract

Under certain drilling conditions, the weighting material particles such as barite can settle out of the drilling fluid. This phenomenon, known as barite sag, can lead to a number of drilling problems including lost circulation, well control difficulties, poor cement job, and stuck pipe. This study investigates barite sag, both experimentally and numerically, in the annulus under flow conditions. Experimental work has been conducted on a large flow loop to investigate the effects of major drilling parameters on barite sag by measuring the circulating fluid density. Results of the tests indicate that the highest sag occurs at low annular velocities and rotational speed and also at high inclination angles. It was observed that at inclination angles less than 60°, for any annular velocity, barite sag is not significant. Eccentricity of a non-rotating inner pipe did not have a significant effect on barite sag. However, effects of inner pipe rotation on barite sag for an eccentric annulus are more significant than concentric case. The simulation part of this study is based on a proposed particle tracking method called “Particle Elimination Technique”. The traveling path of each solid particle is assumed to be a function of size and shape of the particle, fluid velocity and rheology. Based on the estimated traveling path of particles, density of the fluid is updated considering the number of particles whose paths lead to the bottom of the annulus and become motionless. In order to capture the complexities associated with the solid-liquid flow, a lift force is assigned to the solid particles that enable adjustment of the model with experimental results. Comparing the results of numerical simulation to the experimental study on the effects of annular velocity on barite sag in a horizontal annulus shows a good agreement. The numerical simulation was modified from laboratory scale to real wellbore dimensions for practical drilling applications. Results of the simulation show prediction of the density of the drilling fluid in the horizontal section of a wellbore with various lengths and dimensions under different annular velocities.

Keywords:
barite sag numerical simulation experiments annulus power law eccentricity

This work is licensed under a Creative Commons Attribution 4.0 International License. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/

Figures

References:

[1]	Acrivos, A. and Herbolzheimer, E. 1979. Enhanced Sedimentation in Settling Tanks with Inclined Walls. J. Fluid Mechanics, Vol. 92, part 3, 435-457.
[2]	Ahmed, R. 2005. Experimental Study and Modeling of Yield Power-Law Fluid Flow in Pipes and Annuli. TUDRP Semi-Annual Report, May 2005.
[3]	Azouz, I. 1994. Numerical Simulation of Laminar and Turbulent Flows of Wellbore Fluids in Annular Passages of Arbitrary Cross-Section. University of Tulsa Drilling Research Projects, Ph.D. Dissertation.
[4]	Bern, P.A., van Oort, E., Neusstadt, B., Ebeltoft, H., Zurdo, C., Zamora, M., and Slater, K. 1998. Barite Sag: Measurement, Modelling and Management. IADC/SPE 47784, IADC/SPE Asia Pacific Drilling Tech, Jakarta, Indonesia, 7-9 Sept., and SPE Drilling & Completion, March 2000, 25-30.
[5]	Dye, W., Hemphill, T., Gusler, W., and Mullen, G. 1999. Correlation of Ultra-low Shear Rate Viscosity and Dynamic Barite Sag in Invert-Emulsion Drilling Fluids. SPE 56636, Houston, Texas, October.
[6]	Escudier, M.P, Oliveira, P.J., Pinho, F.T. 2001. Fully Developed Laminar Flow Of Purely Viscous Non-Newtonian Liquids Through Annuli, Including Of Eccentricity And Inner-Cylinder Rotation. Heat and Fluid Flow 23 (2001) 52-73.
[7]	Haciislamoglu, M. 1989. Non-Newtonian Fluid Flow in Eccentric Annuli and Its Application to Petroleum Engineering Problems.
[8]	Hanson, P.M., Trigg, T.K., Rachal, G., and Zamora, M. 1990. Investigation of Barite “Sag” in Weighted Drilling Fluids in Highly Deviated Wells. SPE 20423, SPE ATCE, New Orleans, 23-26 Sept.
[9]	Hashemian A. Y. 2005. Numerical Simulation of Laminar Flow of Non-Newtonian Fluids in Eccentric Annuli. MSc. Thesis, University of Tulsa.
[10]	Hashemian, Yahya, 2012“Prediction of Barite Sag in Horizontal Annular Flow,” SPE 160916-STU, International Student Paper Contest ATCE Texas.
[11]	Hashemian A. Y. 2012. Experimental Study and Modeling of Barite Sag in Annular Flow. PhDDissertation, University of Tulsa.
[12]	Hemphill, T., and Ravi, K. (2006) “Turning on Barite Sag with Drillpipe Rotation: Sometimes Surprises Are Really Not Surprises,” AADE, Fluids Conference, Houston, Texas, Nov.
[13]	Nguyen, T.C., Miska, S., Yu, M., and Takach, N., SPE, University of Tulsa (2009) “Predicting Dynamic barite Sag in Newtonian Oil Based Drilling Fluids” SPE 124137, SPE, New Orleans, 4-7 Oct.
[14]	Paslay, P.R., Sathuvalli, U.B., and Payne, M.L. (2007) “A Phenomenological Approach to Analysis of Barite Sag in Drilling Muds,” SPE 110404, SPE ATCE, Anaheim, 11-14 Nov.
[15]	Piercy, N.A.V., Hooper, M.S., Winny, H.F. 1933. Viscous flow through pipes with core. London Edinburgh Dublin Phil. Mag. J. Sci., 15 647-676.
[16]	Shah S.N., Fadili Y. El, Chhabra R.P. 2007. New model for single spherical particle settling velocity in power law (visco inelastic) fluids. Int. J. Multiphase Flow, 33 (2007), pp. 51-66.