Evaluation of Aluminium Alloy for Plasticity Applications

J.D. Amine¹, K. Abubakar^2, and L.T. Tuleun¹

¹Department of Mechanical Engineering, University of Agriculture, Makurdi, Nigeria

²Department of Research, Collaboration and Consultancy, National Centre for Technology Management (NACETEM), Abuja, Nigeria

Cite this paper:
J.D. Amine, K. Abubakar and L.T. Tuleun. Evaluation of Aluminium Alloy for Plasticity Applications. American Journal of Materials Science and Engineering. 2015; 3(1):1-6. doi: 10.12691/ajmse-3-1-1

Abstract

An evaluation of aluminium alloy for plasticity applications was undertaken to bridge the gap in appraising the impact of variation of alloying elements such as magnesium (Mg) and copper (Cu) on plasticity as a mechanical property of the aluminium alloy. To this end, twenty seven (27) samples of aluminium alloys were produced with constituents drawn from 6 % zinc (Zn), 2.5 % - 3.5 % magnesium (Mg), 1.8 % - 3.0 % copper (Cu), 0.03 % manganese (Mn), 0.23 % chromium (Cr) and aluminium (Al) as balance in all cases. 0.1 gram of sulphur (S), which the same as the quantity of iron (Fe) in chromium (Cr) and manganese (Mn), was added to oxidize (eradicate) iron (Fe). Samples were subjected to hardness test; to measure the ability of the alloy to resist plastic deformation and percentage elongation (% e) to unveil the mechanical properties of the alloy. Maximum Vickers hardness (Hv) of 130.7 was displayed by an alloy of 6 % zinc (Zn), 2.5 % magnesium (Mg), 1.8 % copper (Cu), 0.03 % manganese (Mn), 0.23 % chromium (Cr) and aluminium, quenched in water at 490°C and soaked for five (5) hours. The same alloy, non-heat treated, displayed a least Hv of 91.5. Hardness increased from 91.5 Hv in an alloy of 2.5 percentage weight of magnesium to 120.3 Hv in an alloy of 3.5 percentage weight of magnesium. Maximum percentage elongation (% e) of 130.00 was recorded by an alloy of 3.5 % Mg and 2.5 % Cu. A least percentage elongation of 12.00 % was established in an alloy of 3.5 % Mg and 3.0 % Cu. The experiment observed that with increase in percentage weight of magnesium from 2.5 % - 3.0 % - 3.5 %, there was variation from 25.67-18.67- 130.00 respectively in percentage elongation. The alloy with 3.5 % Mg, 1.8 % Cu was recommended for plasticity (% elongation) applications. Investigation of the impacts of other constituents on this alloy may be considered.

Keywords:
magnesium copper mechanical properties plasticity hardness aluminium alloy

This work is licensed under a Creative Commons Attribution 4.0 International License. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/

References:

[1]	Agarwal, L., Rakesh, Y. and Abhishek, S. (2012). Effect of magnesium content on the mechanical properties of Al-Zn-Mg alloys. International Journal on Emerging Technologies 3(1): 137-140.
[2]	Akii, A.O. (1997). Introduction to manufacturing technology, Ambik press, Nigeria. Pp 22-56.
[3]	Al-Rawajfeh, A.E. and Al Qawabah, S.M.A. (2009). Investigation of copper addition on the mechanical properties and corrosion resistance of commercially pure aluminum. Emirates Journal for Engineering Research, 14 (1), 47-52.
[4]	Aniruddha, M. (2010). Tensile test of aluminium at high temperature. National Institute of Technology Rourkela-769008 unpublished. Assessed online at http://ethesis.nitrkl.ac.in/1805/1/final_year_project_report_aniruddhameena.pdf on 22/1/2012.
[5]	Budgen, N.F. (1933). The heat-treatment and annealing of aluminium and its alloy. Sherwood press Inc. Cleveland, Ohio. Pp 43-57.
[6]	Dayan, A. D. and Paine, A. J. (2001). Mechanisms of chromium toxicity, carcinogenicity and allergenicity: Review of the literature from 1985 to 2000. Human and Experimental Toxicology 20 (9): 439-451.
[7]	Dossett, J.L. and Boyer, H.E (2006). Practical heat treating. ASM International. Pp. 17-22.
[8]	Islamgaliev, R.K., Yunusova, N.F., Nikitina, M.A. and Nesterov, K.M., (2010). The effect of alloying elements on superplasticity in an ultrafine-grained aluminum alloy. Advance Material Science. 25 (2010) 241-248.
[9]	John, S., Vidosic, J. P., Harold, V. H. and Donald, D. D. (1996). Strength of Materials (Mechanical properties of materials). Pp 1-68.
[10]	Keith, P. (2000). Process control applications for materials testing and characterization. Assessed online at http://www.industrialheating.com/articles/86135-process-control-applicatios-formaterialstesting-and-characterization on 6/7/ 2011.
[11]	Lyle, J.P., Granger, D.A., and Sanders, R.E. (2005). Aluminium alloys. Assessed online at http://en.wikipedia.org/wiki/ullmann%27s_encyclopedia_of_industrial_chemistry/ww.v.engineering.de/pro.of.Al.pdf on 31/03/2011.
[12]	Mohammed, S. (2010). A guide to alloying of non-ferrous metals. Unpublished, paper presented during an in-house seminar at the National Metallurgical Centre, Jos. Pp 1-15.
[13]	Murray, M. (2002). Friction stir processing creates aluminum-alloy superplasticity. Assessed online at http://www.industrialheating.com/Articles/Cover_Story/192d4d11febb 7010VgnVCM100000f932a8c0 on 1/11/2011.
[14]	Samsudi, S. (2011). Mechanical properties and testing lecture note on materials science (SSP 2412). Physics Dept. Faculty of Science, Universiti Teknologi Malaysia.
[15]	Tuleun L.T., Amine, J.D. and Abubakar, K.,(2014). Effect of Variation in Magnesium and Copper on Mechanical Properties of X7475 Aluminium Alloy.” American Journal of Materials Science and Engineering, vol. 2, no. 4 (2014): 54-61.
[16]	Zhenguo, C. (2010). Superplasticity of coarse grained aluminum alloys. Assessed online at http://www.materials.manchester.ac.uk/documents/research/epsrc/latest/Project%20Number%203%20%20 Superplasticity%20of%20coarse%20grained%20aluminium%20alloys.pdf on 28/10/2010.