Performance of Airlift Pumps: Single-Stage vs. Multistage Air Injection

A-F. Mahrous^{1, 2,}

¹Mechanical Engineering Department, Taif University, Al-huwayah, KSA

²Mechanical Power Engineering Department, Menoufiya University, Shebin El-Kom, Egypt

Cite this paper:
A-F. Mahrous. Performance of Airlift Pumps: Single-Stage vs. Multistage Air Injection. American Journal of Mechanical Engineering. 2014; 2(1):28-33. doi: 10.12691/ajme-2-1-5

Abstract

Airlift pumps provide reliable means of artificially lifting of liquids or liquid-solid mixtures from deep wells or vessels. This paper presents a numerical investigation into the effects of air injection strategy, single-stage vs. multistage air injection, on the airlift pump performance. A numerical model of airlift pump, based on the concept of momentum balance, was developed and validated against available experimental data. Predictive studies on model airlift pump with different arrangements of injected compressed air were numerically carried out. Numerical results showed that applying the commonly used single-stage air injection causes a steep change in the pump output-input characteristic curve followed by a fast decay after the optimum point. Injecting the compressed air in a number of air injection stages, on the other hand, was shown to increase the range of bubbly-slug flow regime as well as the pump operating window close to the optimum conditions. Improvement in the pump performance at higher degrees of air input mass flow rates is expected when employing multistage air injection.

Keywords:
airlift pumps two-phase flow multistage air injection

This work is licensed under a Creative Commons Attribution 4.0 International License. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/

References:

[1]	Parker, G.J., The effect of foot piece design on the performance of a small diameter airlift pump. Int. J. Heat and Fluid Flow, 1980. 2(4): p. 245-252.
[2]	“Composites test fixtures, Iosipescu shear, ASTM D 5379”. Instron. [online] Available: http://www.instron.com.
[3]	Leeuwen, D., A. et al., “Comparison of static shear test methodologies, test results and analysis”[online] Available: http://www.upwind.eu/pdf/shear%20comp.arison%20-%20paper%20wind%20energy%20conference%20china.pdf.
[4]	Mansour, H. and M.F. Khalil, Effect of air injection method on the performance of airlift pump. Mansoura Eng. J., 1990. 15(2): p. 107-118.
[5]	Khalil, M.F., Elshorbagy, K. A., Kassab, S. Z. and Fahmy, R. I., Effect of air injection method on the performance of an airlift pump. Int. J. Heat and Fluid Flow, 1999. 20: p. 598-604.
[6]	WYOMING TEST FIXTURES INC. [online] Available: http://www.wyomingtestfixtures.com/products.html>.
[7]	Chakherlou, T. N., Maleki, H. N., Abazadeh, B., Aghdam, A. B. Investigating bolt clamping force effect on the mixed mode fracture strenght and stress intensity factor for an edge in PMMA specimens. Elsevier, Material Science and Engineering: A,533, s. 71-81, 2012.
[8]	Khalil, M.F. and H. Mansour, Improvement of the performance of an airlift pump by means of surfactants. Mansoura Eng. J., 1990. 15(2): p. 119-129.
[9]	Mahrous, A.-F., Numerical Study of Solid Particles-Based Airlift Pump Performance. WSEAS Transactions on Applied and Theoretical Mechanics, 2012. 7(3): p. 221-230.
[10]	Fagerholt, E., Dorum, C., Borvik, T., Laukli, H. I., Hooperstad, O. S.: Experimental and numerical investigation of fracture in a cast aluminium alloy. Elsevier, International Journal of Solids and Structures, s. 3352-3365, 2010.
[11]	Hasanpour, R., Choupani, N., “Rock fracture characterization using the modified Arcan test specimen”. Elsevier, International Journal of Rock Mechanics and Mining Sciences, Volume 46, 2009, s. 346-354.
[12]	Mahrous, A.-F., Performance Study of an Airlift Pump with Bent Riser Tube. WSEAS Transactions on Applied and Theoretical Mechanics, 2013. 8(2): p. 136-145.
[13]	Mahrous, A.-F., Airlift Pump with a Gradually Enlarged Segment in the Riser Tube. ASME Journal of Fluids Engineering, 2013. 135(3): p. 031301.
[14]	Pucillo, G. P., Grasso, M., Penta, F., Pinto, P., “On the mechanical characterization of materials by Arcan-type specimens” Science Direct, Engineering Fracture Mechanics, Volume 78, s. 1729-1741. 2011.
[15]	Dantec Dynamics, “Fast Stress and Strain Analysis with Q-100” [online] Available: http://www.dantecdynamics.com/.
[16]	Shimizu, Y., Tojo, C., Suzuki, M., Takagaki, Y. and Saito, T., A study on the air-lift pumping system for manganese nodule mining, in Proc. of the 2nd International Offshore and Polar Engineering Conference. 1992: San Francisco, USA. p. 490-497.
[17]	Reinemann, D.J. and M.B. Timmons, Predicting oxygen transfer and total dissolved gas pressure in airlift pumping. Aquacultural Engineering, 1989. 8: p. 29-46.
[18]	Trebuňa, F., Šimčák, F.,Príručka experimentálnej mechaniky, Košice: Typopress, 2007. 1525 s.
[19]	Tiziani, H., J, “Kohärent-optische Verfahren in der Oberflächenmeβtechnik”.Universität Stuttgart. Technisches Messen, 1991. cit. 2012-11-3]. [Online] Available: http://elib.uni-stuttga rt.de/o pus/volltexte/ 2011/6148/pdf/tiz93.pdf.
[20]	Nenes, A., Assimacopoulos, D., Markatos, N. and Mitsoulis, E., Simulation of airlift pumps for deep water wells. The Canadian Journal of Chemical Engineering, 1996. 74: p. 448-456.
[21]	Dedegil, M.Y., Principles of airlift techniques, in Encyclopedia of Fluid Mechanics, N.P. Chereimisinoff, Editor. 1986, Gulf, Houston, TX. p. Chapter 12.
[22]	Clauss, G.F., Investigation of characteristic data of air lifting in ocean mining (Untersuchung der kenngrőben des airlifts beim Einsatz im ozeanbergbau). Erdől-Erdgas-Zeitschrift, 1971. 87: p. 57-66 (In German).
[23]	Boës, C., Düring, R. and Wasserroth, E., Airlift as a drive for single and double pipe conveying plants (Airlift als antrieb für einrohr-und doppelrohr-főrderanlagen). főrdern und heben, 1972. 22(7): p. 367-378 (In German).
[24]	Yoshinaga, T. and Y. Sato, Performance of an air-lift pump for conveying coarse particles. Int. J. Multiphase Flow, 1996. 22(2): p. 223-238.
[25]	Margaris, D.P. and D.G. Papanikas, A generalized gas-liquid-solid three-phase flow analysis for airlift pump design. Trans. of the ASME, J. of Fluids Engineering, 1997. 119: p. 995-1002.
[26]	Hatta, N., Fujimoto, H., Isobe, M. and Kang, J., Theoretical analysis of flow characteristics of multiphase mixtures in a vertical Pipe. Int. J. Multiphase Flow, 1998. 24(4): p. 539-561.
[27]	Mahrous, A.-F., Performance of airlift pumps, in Mechanical Power Engineering Dept. 2001, Menoufiya University, Egypt.
[28]	Weber, M. and Y. Dedegil, Transport of solids according to the air-lift principle, in Proc. 4th International Conf. on the Hydraulic Transport of Solids in Pipes. 1976. p. H1-1 - H1-23.
[29]	Yoshinaga, T., Sato, Y. and Sadatomi, M., Characteristics of air-lift pump for conveying solid particles. Jap. J. Multiphase Flow, 1990. 4: p. 174-191 (in Japanese).
[30]	Lawniczak, F., Francois, P., Scrivener, O., Kastrinakis, E.G. and Nychas, S.G., The efficiency of short airlift pumps operating at low submergence ratios. The Canadian Journal of Chemical Engineering, 1999. 77: p. 3-10.
[31]	Fujimoto, H., Murakami, S., Omura, A., and Takuda, H., Effect of local pipe bends on pump performance of a small air-lift system in transporting solid particles. International Journal of Heat and Fluid Flow, 2004. 25: p. 996-1005.