American Journal of Mechanical Engineering
ISSN (Print): 2328-4102 ISSN (Online): 2328-4110 Website: http://www.sciepub.com/journal/ajme Editor-in-chief: Kambiz Ebrahimi, Dr. SRINIVASA VENKATESHAPPA CHIKKOL
Open Access
Journal Browser
Go
American Journal of Mechanical Engineering. 2016, 4(7), 280-288
DOI: 10.12691/ajme-4-7-10
Open AccessSpecial Issue

Dynamic Analysis of Lathe Machine Tool

Darina Hroncová1, , Peter Sivák1, Jozef Filas1 and Michal Kicko1

1Department of Mechatronics, Technical University of Kosice, Faculty of Mechanical Engineering, Kosice, Slovakia

Pub. Date: December 17, 2016

Cite this paper:
Darina Hroncová, Peter Sivák, Jozef Filas and Michal Kicko. Dynamic Analysis of Lathe Machine Tool. American Journal of Mechanical Engineering. 2016; 4(7):280-288. doi: 10.12691/ajme-4-7-10

Abstract

The thesis presents a theoretical analysis of the task, while practical knowledge of selected parts of the dynamics is used to solve individual involved transfers. Further for the two types of programs includes detailed diagrams that is rev/min (rpm) increasing and rev/min reduction. The centre lathe is the object of exploring. Specifically transmission parts such as shafts, gears and pulleys then it is electric drive device, and finally driven parts such as spindle and chuck. Analyze of angular velocities, moments of inertia, kinetic energy, performance and labor of each part of the kit is performed using reduction method, and the system is reduced to a first member, which is an electric motor. We have developed integration of individual gears for the machining modes. Specifically for conventional turning 2800 rpm and for winding springs 14 rpm. In technical practice it is not possible to measure two same results of performance parameters, for reason of passive resistance.

Keywords:
dynamical equations of the motion kinetic energy dynamic analysis of lathe reduction method

Creative CommonsThis work is licensed under a Creative Commons Attribution 4.0 International License. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/

Figures

Figure of 28

References:

[1]  Brychta, J.: Výrobní stroje obráběcí, VŠB-TU, , Česko, 2003.
 
[2]  Varchola, M. Madáč, K.: Obrábacie stroje. TUKE, Košice, Slovakia, 2004.
 
[3]  Záhorec, O., Caban, S., Dynamika, TUKE, Košice, Slovakia, 2002.
 
[4]  Delyová, I., Frankovský, P., Hroncová, D., Kinematic analysis of movement of a point of a simple mechanism,” 4th International Conference Modelling of mechanical and mechatronics systems, KAMaM, Technical university Košice, Herľany, Slovakia, 2011.
 
[5]  Skočilas, J., Skočilasová, B., Soukup, J., Investigation and vibration of vehicle mechanical model. In: Dynamika tuhých a deformovatelných těles 2011 - Sborník přednášek z 9. mezinárodní konference, FVTM UJEP, Ústí nad Labem, Česko, 2011.
 
[6]  Svoboda, M., Soukup, J., “Analytical solutions of motion equations of railway car, determination of bazic geometric, mass and stiffness parameters,” Dynamika tuhých a deformovatelných těles 2011 - Sborník přednášek z 9. mezinárodní conference, FVTM UJEP, Ústí nad Labem, Česko, 2011.
 
[7]  Virgala, I., Frankovský, P., Kenderová, M.: Friction Effect Analysis of a DC Motor. In: American Journal of Mechanical Engineering, Vol. 1, No. 1, p. 1-5, 2013.
 
[8]  Novotný, L., Tsunori, M., Creation of Imperfections for Welding Simulations, In:“CMES: Computer Modeling in Engineering & Sciences”, Vol.82, Nos.3&4, p. 253-264, 2011.