American Journal of Mechanical Engineering
ISSN (Print): 2328-4102 ISSN (Online): 2328-4110 Website: http://www.sciepub.com/journal/ajme Editor-in-chief: Kambiz Ebrahimi, Dr. SRINIVASA VENKATESHAPPA CHIKKOL
Open Access
Journal Browser
Go
American Journal of Mechanical Engineering. 2013, 1(7), 403-406
DOI: 10.12691/ajme-1-7-50
Open AccessArticle

Possibility of Carrying Capacity Increasing of Anchor Bolts in Heavy Equipments of Metallurgical Plants

František Trebuňa1, František Šimčák1, and Jozef Bocko1

1Department of Applied Mechanics and Mechatronics, Faculty of Mechanical Engineering, Technical university of Košice, Košice, Slovakia

Pub. Date: October 21, 2013

Cite this paper:
František Trebuňa, František Šimčák and Jozef Bocko. Possibility of Carrying Capacity Increasing of Anchor Bolts in Heavy Equipments of Metallurgical Plants. American Journal of Mechanical Engineering. 2013; 1(7):403-406. doi: 10.12691/ajme-1-7-50

Abstract

Abstract Anchor bolts in heavy machines of metallurgical plants are often, from the point of view of their carrying capacity, limiting factor in increasing productivity. This paper presents some possibilities of increasing strength of anchor bolts using numerical and experimental methods of mechanics. Proposed and verified procedures allow determining the actual stress states during tightening the anchor bolts and nuts and reduce dynamic loads in bolts as well as in operating machines.

Keywords:
anchor bolts dynamic loading numerical and experimental methods of mechanics

Creative CommonsThis work is licensed under a Creative Commons Attribution 4.0 International License. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/

Figures

Figure of 14

References:

[1]  Trebuňa, F et al., Vibration of converter pedestal, suggestions for possible structural modifications and their verification. SjF TU, Košice, 2005.
 
[2]  Trebuňa, F., Šimčak, F., Bocko, J., Decreasing of vibration amplitudes of the converter pedestal by design changes and changes in prestress of the bolted joints, Engineering Failure Analysis, 16, 2009, p. 262-272.
 
[3]  Trebuňa F. et al., Riešenie predlženia životnosti liacieho stojana s využitím záverov doterajších analýz a návrhy úprav pre predlženie životnosti liacieho stojana. SjF TU, Košice, 2009.
 
[4]  Trebuňa, F., Šimčák, F., Príručka experimentálnej mechaniky. Typopress, Košice, 2007.
 
[5]  Kobayshi, A. S., Handbook on Experimental Mechanics, VCH Verlagsgesellschaft mbH, Weinheim, Germany. 1993.
 
[6]  Shigley, J. E., Mischke, Ch. R., Budynas, R. G., Mechanical Engineering Design, McGraw-Hill Professional, 2004.
 
[7]  Dejl, Z., Konstrukce strojů zařízení I., Montanex, a.s. Ostrava 2000.
 
[8]  Berger C., Schaumann P., Stolle C. and Marten F., Fatigue strength of high strength bolts with large diameters, IGF-Bericht 14728 N, 2008 ( in German).
 
[9]  Fukuoka T. and Nomura M., Proposition of Helical Thread Modelling with accurate Geometry and Finite Element Analysis, Journal of Pressure Vessel Technology, Vol. 130, 2008, pp. 011204-1 - 011204-6.